Devices You Need to Install a New Bath Tub
Devices You Need to Install a New Bath Tub
Blog Article
What are your beliefs on How to Install a Bathtub Yourself?
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard task. If the old tub is easily obtainable, the task can move quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Ensure you have certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require an expert plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your bathroom if you have already bought a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the maker offered backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind ought to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wooden boards under its feet, put the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the level reads degree.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last position.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, bring about issues with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads on Tools You Need to Install a New Bathtub , I was thinking sharing that piece of writing was essential. Kindly take a moment to distribute this blog entry if you appreciated it. Thanks a lot for your time. Come back soon.
Book A Service Call
Report this page